RE: [Brahms-dev-l] making dst files

Hi Flemming,

      I was looking into "BrTofRdoModule.cxx" and checking if I was reading the slewing parameters correctly from database,
I found the following 
 -------------
 for(Int_t h = 0; h < hits->GetEntries(); h++) {
    BrTofDig* hit = (BrTofDig*)hits->At(h);

    Int_t slat = hit->GetSlatno();

       if (fUseSlewing) {
      slewt1 = fCalibration->GetTopSlewPar1(slat);
      slewt2 = fCalibration->GetTopSlewPar2(slat);
      slewb1 = fCalibration->GetBotSlewPar1(slat);
      slewb2 = fCalibration->GetBotSlewPar2(slat);

      cout<<"slat :"<<slat<<endl;

      cout<<"slewt1 :"<<slewt1<<endl;
      cout<<"slewt2 :"<<slewt2<<endl;
      cout<<"slewb1 :"<<slewb1<<endl;
      cout<<"slewb2 :"<<slewb2<<endl;

      if (slewb2 == BrTofCalibration::kCalException)
	continue;
    }
    
 }
-------------

slat :13
slewt1 :0.0841689
slewt2 :34.5026
slewb1 :0.0841689
slewb2 :29.4853
slat :2
slewt1 :-0.12063
slewt2 :22.563
slewb1 :-0.12063
slewb2 :39.3138
slat :60
slewt1 :-0.739168
slewt2 :22.9963
slewb1 :-0.739168
slewb2 :18.8778
slat :61
slewt1 :-0.752743
slewt2 :25.4482
slewb1 :-0.752743
slewb2 :15.9752
slat :62
slewt1 :-0.707273
slewt2 :17.5353
slewb1 :-0.707273
slewb2 :17.0119

------------------------

I thought the slat number for H1 goes upto 40. But as you can see above some slat numbers are > 40 .
Is there a global slat number for the hits which gets converted to the actual slat number inside the
code which accesses the calibration parameters or this is a bug?

Selemon,

-----Original Message-----
From: flemming videbaek [mailto:videbaek@rcf.rhic.bnl.gov]
Sent: Sun 8/21/2005 7:31 PM
To: Bekele, Selemon; brahms-dev-l@lists.bnl.gov
Subject: Re: [Brahms-dev-l] making dst files
 
Hi
I assume you have solved the problem since subsequent submissions from you
seem to have worked.
Please give feedback to the list if you actually solve problems that have
been announched. This benifits all

regards
    Flemming
----------------------------------------------------------------
Flemming Videbaek
Physics Department
Brookhaven National Laboratory

e-mail: videbaek@bnl.gov
phone: 631-344-4106
----- Original Message ----- 
From: "Bekele, Selemon" <bekeleku@ku.edu>
To: <brahms-dev-l@lists.bnl.gov>
Sent: Friday, August 19, 2005 6:40 PM
Subject: [Brahms-dev-l] making dst files


>
> Hi All,
>
>    I was trying to make a dst to test H1 and H2 calibratios. I did
>
> bramreco@rcas0032:~/DataProduction/run05/cucu/200/dst> ./submitDst.perl
12225
>
>     which excuted makeDst.rb as
>
>
./makeDst.rb --userName=tigist --email=tigist@bnl.gov --inputProductionNo=1 
--outputProductionNo=1 --beginRun=12225 --endRun=12225 --condor_q=rcrs5
>
>     but the output file does not seem to be written out properly. I also
checked the files
>
> /brahms/data21/data/run05/cucu/200/r12225/log/dst012225v6p1.out
> /brahms/data21/data/run05/cucu/200/r12225/log/dst012225v6p1.err
>
>    both of which are empty. I tried with another run but got the same
results. May be I am missing something.
> any ideas?
>
>
> Selemon,
>
> _______________________________________________
> Brahms-dev-l mailing list
> Brahms-dev-l@lists.bnl.gov
> http://lists.bnl.gov/mailman/listinfo/brahms-dev-l
>



_______________________________________________
Brahms-dev-l mailing list
Brahms-dev-l@lists.bnl.gov
http://lists.bnl.gov/mailman/listinfo/brahms-dev-l